2013 Buick Verano Ignition Transponder Chip Key Programming Instructions

Description
How to Program a 2013 Buick Verano Ignition Transponder Chip Key

Step by Step How to Programming Instructions:
 
These programming procedures are only good for USA built vehicles.
 
Use these procedures if you have a key or flip key.
 

Can I program a duplicate key for this vehicle?

Yes, once you have had the new key cut by a Locksmith use the following instructions.

1. Insert  an existing programmed working key into the ignition cylinder.      

2. Turn ignition to the ON position for 5 seconds, then back to OFF position.

3. Remove the existing key and within 5 seconds insert new key and turn it to the ON position for 5 seconds.

4. Turn key OFF then back to ON. The key is now programmed. Start vehicle to test key. 

 
Can I program a new key myself if I have no working keys?
No, Contact a Locksmith to program.
 

Use these procedures if you have a Smart Key Fob.
 
Programming with a Recognized Transmitter (Keyless Access Vehicles Only)
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all of the transmitters, both currently recognized and new, must be with you.
 
1. Place the recognized transmitter(s) in the cupholder.

2. Insert the vehicle key of the new transmitter into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4 or 5.

3. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console cupholder. The cupholder liner will need to be pulled out to access the transmitter pocket.
 
4. Press the ignition. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.
 
5. Remove the transmitter from the transmitter pocket and press Unlock. To program additional transmitters, repeat Steps 3 through 5. When all additional transmitters are programmed, press and hold the ignition for 10 seconds to exit programming mode.
 
 
Programming without a Recognized Transmitter (Keyless Access Vehicles Only)
If there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This feature is not available in Canada. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you.
 
1. Insert the vehicle key of the transmitter into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within 10 seconds. The Driver Information Center (DIC) displays REMOTE LEARN PENDING, PLEASE WAIT. 
 
2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press the ignition. The DIC displays will again show REMOTE LEARN PENDING, PLEASE WAIT.
 
3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.
 
4. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console cupholder. The cupholder liner will need to be pulled out to access the transmitter pocket.
 
5. Press the ignition. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter. 6. Remove the transmitter from the transmitter pocket and press Unlock. To program additional transmitters, repeat Steps 4 through
 
6. When all additional transmitters are programmed, press and hold the ignition for 10 seconds to exit programming mode. 
Video

Need a Local Locksmith?

Go to LocateALocksmith.com
 
or 
Call (877) 782-5192 to find a Locksmith in your area.

 Auto Transponder Keys, Chip Keys, Ignition Keys all at up to 70% off dealer prices!