2014 Mitsubishi Mirage Ignition Smart Chip Key Programming Instructions

Description
How to Program a 2014 Mitsubishi Mirage Ignition Smart Chip Key 

Step by Step How to Programming Instructions:

Use these instructions if you have Remote Head Key System.
To add a key, you must already have two programmed keys. You can have a total of 8 keys programmed.  
 
1. Insert the first valid key into the ignition switch and turn the key to the “ON” position for 5 seconds.
 
2. Turn the key to the “OFF” position and remove the first key.
 
3. Within 30 seconds of removing the first key, insert the second valid key into the ignition and turn it to the “ON” position. Approximately 10 seconds later, the immobilizer display will start to blink.
 
4. When the immobilizer display starts blinking, turn the second valid key to the “OFF” position and remove it. Within 30 seconds after doing so, insert a blank immobilizer key into the ignition switch and turn it to the “ON” position. Perform this operation no more than 30 seconds after the immobilizer display starts blinking. When programming is complete, the immobilizer display will come on for 30 seconds then go off. If an error occurs, the blinking immobilizer display will go off during the procedure. 
 
5. If you wish to register another key, perform the process again from step 1. 
 
 
Use these instructions if you have the Fast Key Smart Key System. 
You can program new F.A.S.T.-keys to the system if you have two valid (already programmed) F.A.S.T.-keys and a blank (not programmed) F.A.S.T.-key. For F.A.S.T.-key programming, follow the procedures below.
 
1. Open the driver’s door.  NOTE: Keep the driver’s door open until F.A.S.T.- key programming is finished. Do not open or close other doors.
 
2. While carrying the first valid F.A.S.T.- key, put the operation mode in ON. (Perform the following procedure within 30 seconds.)
 
3. Insert the new F.A.S.T. key into the key slot. (Located above cup holder in center console).
 
4. With the first valid F.A.S.T.-key, press the UNLOCK button for 4 to 10 seconds and press the LOCK button during this time.
 
5. Release in sequence the LOCK and UNLOCK buttons within 10 seconds of pressing the LOCK button in step 4. (Perform the following procedure within 30 seconds.)
 
6. With the second valid F.A.S.T.-key, press the UNLOCK button for 4 to 10 seconds and press the LOCK button during this time.
 
7. Release in sequence the LOCK and UNLOCK buttons within 10 seconds of pressing the LOCK button in step 6. The immobilizer warning light will blink. 
When registration of ID code is complete, the buzzer will sound three times and the immobilizer display will come on for 30 seconds. If an error occurs, F.A.S.T.-key programming will be terminated and the buzzer will sound for 3 seconds
 
NOTE  F.A.S.T.-key programming will be terminated if the operation mode is put in OFF before the immobilizer display starts blinking.
 
8. If you wish to register another F.A.S.T.- key, repeat the process from step 1 after the operation mode is put in OFF..
 
NOTE  The immobilizer display will go off immediately if the operation mode is put in OFF.  It is not possible to register a F.A.S.T.-key if the immobilizer display goes off during the procedure.  
 
 
If all keys are lost with either the Key System or the F.A.S.T. Key System 
This vehicle is not on board programmable and requires a qualified professional to program smart key remote fobs.

1. Locate an automotive locksmith in your area using the phone number.

2. If your vehicle is still mobile, it may save you money by driving to the locksmith instead of having them come to you.

3. The locksmith will then hook up specialized computer equipment to your vehicle in order to program the smart key remote fob.